OPPO A79 5G (CPH2557) Test Point for Unbrick/Flashing (MediaTek BROM Mode)

Introduction
Hello friends, welcome to GSM Helpful. In this guide, I’m going to show you the OPPO A79 5G (CPH2553, CPH2557) test point for entering EDL mode, also known as MediaTek BROM port. This method works for OPPO A79 5G (CPH2553, CPH2557) models CPH2553, CPH2557.

What is EDL Mode ?
EDL mode (Emergency Download mode) is used to unbrick or flash MedaiTek-powered phones. If your OPPO A79 5G (CPH2553, CPH2557) is dead or stuck, EDL mode helps to connect the phone to PC for flashing firmware.

Steps to Find and Use OPPO A79 5G (CPH2553, CPH2557) Test Point

Switch off the phone and remove SIM tray.
Open the back cover carefully.
Disconnect the battery connector from motherboard.
Locate the two small test points on the board.
Short these test points using tweezers.
While shorting, connect the USB cable to your PC.

If done correctly, your PC will detect the phone as MediaTek BROM Mode. Now you can flash the device using any MediaTek flashing tool.

Important Notes

Be careful while opening the phone to avoid damage.
Always use correct firmware for your model.

Conclusion
That’s how you can use the OPPO A79 5G (CPH2553, CPH2557) test point for EDL mode. This method is very helpful for fixing dead or bricked OPPO A79 5G (CPH2553, CPH2557) devices.

Difference Between Hard Bricked and Soft Bricked Phones

Today I’ll explain the difference between hard bricked and soft bricked phones in a simple way. Many people confuse these terms, but after reading this, you’ll understand clearly.

What is Soft Bricked?

Phone is stuck on boot logo or in bootloop.
Can still enter recovery mode or fastboot mode.
Usually happens after wrong flashing, failed update, or software error.
Easy to fix by flashing the correct firmware.

What is Hard Bricked?

Phone is completely dead – no charging, no display, no vibration.
Cannot enter recovery or fastboot mode.
Sometimes not detected by PC in normal mode.
Usually caused by flashing wrong firmware or interrupting flash process.
Requires EDL mode, test points, or professional tools to fix.

Quick Comparison

Soft Brick: Phone is “sick but alive.”
Hard Brick: Phone is “in coma and needs surgery.” 😅

How to Access the EDL Test Point on OPPO A79 5G (CPH2553, CPH2557)

⚠️ Disclaimer: This process involves hardware manipulation. Attempt it only if you’re confident, or consult a professional. It may void your warranty.

Steps to Enter EDL Mode via Test Point:

Power Off and Disassemble the Device
Carefully open the back panel of your OPPO A79 5G (CPH2553, CPH2557) using a heat gun or plastic pry tool. Be gentle to avoid damaging the internals.
Locate the EDL Test Point
Refer to a motherboard schematic diagram or a test point guide specific to your model (CPH2553, CPH2557). The EDL point is usually marked or located near the USB port or chipset.
Short the Test Point to Ground
Use tweezers or a small conductive wire to short the EDL point to the ground. This should be done gently and accurately.
Connect to a Computer via USB
While shorting the test point, connect your phone to the PC. Your computer should detect the device in EDL Mediatek Dimensity 6300 Mode.
Flash the Firmware
Use compatible flashing tools (for Mediatek Dimensity 6300) and the correct stock firmware for your device model. Begin the flashing process to restore functionality.

Important Tips and Considerations

✅ Model Specific Tools

Always use the exact firmware and flashing tools compatible with your model number (CPH2553, CPH2557).

🔐 Data Loss

EDL flashing typically wipes all user data. Backup, if possible, before attempting.

⚠️ Risk of Permanent Damage

Incorrect handling of the motherboard or wrong firmware flash can brick your device permanently.

Conclusion

The EDL test point on the OPPO A79 5G (CPH2553, CPH2557) is a powerful recovery solution for users dealing with severe software issues. Whether your device is bricked, suffering from a failed update, or in need of advanced repair, understanding how to safely use the EDL mode can be a game-changer.

However, due to the risks involved, always proceed with caution. If you're unsure, it’s wise to consult a qualified technician. When done correctly, this method can save your phone — and a lot of money in repair costs.

Keywords optimized for SEO: