How to Find the Test Point on Redmi Note 14 5G (beryl) | Unbrick & Bypass FRP

The Redmi Note 14 5G (beryl) is a feature-packed smartphone, but like any device, it can encounter issues such as bootloops, FRP locks, or software corruption. In such situations, entering EDL (Emergency Download Mode) using the Test Point method becomes essential for troubleshooting and recovery.

This guide will help you locate the Redmi Note 14 5G Test Point, enter EDL Mode, and use it to flash firmware or remove FRP locks.

What is the Test Point Method?

The Test Point method involves shorting specific points on the motherboard to force the phone into Emergency Download Mode (EDL). This mode allows you to communicate with the phone at a hardware level using flashing tools, enabling repairs such as:

• Resolving bootloop or bricking issues.
• Flashing stock firmware.
• Bypassing FRP locks.

For the Redmi Note 14 5G (beryl), the Test Point method works seamlessly across all variants, including 24094RAD4G, 24094RAD4I, 24094RAD4C, 2409FPCC4G.

Why Do You Need the Test Point Method?

The Test Point method is particularly useful when:

1. The phone does not boot or is stuck in a bootloop.
2. Fastboot or Recovery modes are inaccessible.
3. You need to flash stock ROM or remove an FRP lock.

Tools Required

To perform the Test Point method, you’ll need:

1. Redmi Note 14 5G (beryl) smartphone.
2. Precision screwdriver to open the back panel.
3. Tweezers or a conductive tool to short the Test Points.
4. USB cable and a PC with Mediatek USB drivers installed.
5. Flash tools such as Mi Flash Tool or SP Flash Tool.
6. Stock firmware for the 24094RAD4G, 24094RAD4I, 24094RAD4C, 2409FPCC4G variant.

Steps to Access EDL Mode via Test Point

1. Power Off the Device

• Ensure the phone is completely turned off. If it’s stuck, hold the power button until it shuts down.

2. Disassemble the Phone

• Use a pry tool to carefully remove the back cover of the device.
• Unscrew and remove the protective cover over the motherboard.

3. Locate the Test Points

• Find the EDL Point Redmi Note 14 5G Test Point on the motherboard. These points are usually located near the battery connector or other critical components.
• Refer to the image below for the exact location (Insert Picture Here).

4. Short the Test Points

• Use tweezers or a conductive tool to short the identified Test Points.
• While holding the Test Points shorted, connect the phone to your PC using a USB cable.

5. Verify EDL Mode

• Open Device Manager on your PC to check if the device is recognized as Mediatek.

6. Flash Firmware or Remove FRP Lock

• Launch Mi Flash Tool or SP Flash Tool to flash the stock firmware or remove the FRP lock.

Key Points to Remember

1. Firmware Compatibility

   • Always use the correct firmware version for your device variant (24094RAD4G, 24094RAD4I, 24094RAD4C, 2409FPCC4G) to avoid bricking the phone.

2. Battery Charge

   • Ensure the battery is at least 50% charged before performing any flashing operations.

3. Driver Installation

   • Install Mediatek USB drivers to ensure the phone is recognized in EDL Mode.

4. Handle with Care

   • Be cautious while opening the device and shorting the Test Points to avoid damaging internal components.

Topic Covered:

1. EDL Point Redmi Note 14 5G Test Point
2. EDL Point beryl Test Point
3. EDL Point 24094RAD4G, 24094RAD4I, 24094RAD4C, 2409FPCC4G Test Point
4. Redmi Note 14 5G test point
5. beryl EDL point
6. Xiaomi Mi Note 14 5G test point
7. Redmi Note 14 5G Brom Mode
8. POCO M7 Pro 5G test point[6]
9. Secondary (LSI) Keywords):
10. Unbrick Redmi Note 14 5G
11. beryl dead boot repair
12. MediaTek Dimensity 7025 test point
13. Bypass FRP Redmi Note 14 5G
14. Flash firmware Redmi Note 14 5G
15. MTK USB Port
16. Emergency Download Mode MTK
17. beryl unbrick tool

Conclusion

The Redmi Note 14 5G (beryl) Test Point is a vital tool for troubleshooting issues like bootloops, FRP locks, and software corruption. By following this guide and using the suggested images, you can safely access EDL Mode and resolve these problems.

Always ensure you have the correct firmware and tools before proceeding. If done correctly, the Test Point method is an effective way to recover your Redmi Note 14 5G and restore it to working condition.