04 December 2015

Micromax Bolt A34 Pattern Lock, Hang on logo, Restarting done with simple method

Posted by
04 December 2015
Sponsored Links

Must Read Users:
This tutorial tested by me without any risk but this issue do fix to need box, if you use this tutorial or trick so remember you can't save any data like contacts, images, videos etc because this is full factory reset, and also must check your device battery if not full charged so coming error between do process, if error coming then your device will be dead so remember must this topic and also check micro usb cable if not good then your device not connect or other error show like usb not recognized  with box tool, this tricks many problem solved like security lock, phone lock, memory card lock, contact lock, photo gallery lock, videos lock etc not let's go how to this many problem solve by box tool see below.

Required for above mention problem solution:

1. Micromax Bolt A34 device (no need to battery)
2. Volcano box or Miracle box (this tutorial using volcano box)
3. Micro usb cable
4. Computer or Laptop

Procedure:

Read Info:
1. Open Volcano box
2. Go to tab of SPD(Spreadtrum) CPU
3. Choose Built-in Boot_14(6820/8810) in Boot option
4. Click on Read Info option
5. Tick on Auto-detect Pinouts option
6. Connect device with Pro Series Service Cable (7pin)
7. Now last click on Start button
8. Wait until full process

Micromax Bolt A34 Read Info done with Volcano box Screenshot

Micromax Bolt A34 Read Info done with Volcano box Logs
  Available Ports:COM1 COM45 COM90   
  Detection initiated...  
  Vcc: null  
  Gnd: 7  
  Analyzing D+ and D-...  
  D+ = 4, D- = 3  
  Detection D+/D- with 1.11 seconds.  
  Continue to detect BOOT pin...  
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)  
  UsbVcc(VCC) = 1, BOOT(Pull Down) = 5  
  Setting...  
  Find USB device:SCI USB2Serial (COM177), (VID_1782&PID_4D00)  
  Pinouts setting complete!  
  Waiting for phone's response, press the Power on the phone    
  Internal version: SPRD3  
  Boot downloaded.  
  Start boot please wait a moment....  
  Spreadtrum Boot Block version 1.1  
  Boot downloaded.  
  CPU TYPE:SC8810/6820 [88100001]  
  Flash ID: 009800BC90667600  
  Flash Type:[TOSHIBA] TYBC0A111236KC10  
  FLASH LEN:0x20000000  
  mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjaluna),1536k(fastboot_logo),2560k(productinfo),3328k(fixnv),3328k(backupfixnv),3m(boot_logo),3328k(runtimenv),8m(boot),8m(recovery),200m(system),202m(userdata),60m(cache),256k(misc),10m(modem),5m(dsp),512k(kpanic)  
 >>Analysis flash internal data successfully.  

Format
1. Open Volcano box
2. Go to tab of SPD(Spreadtrum) CPU
3. Choose Built-in Boot_14(6820/8810) in Boot option
4. Click on Format option
5. Tick on Auto-detect Pinouts option
6. Connect device with Pro Series Service Cable (7pin)
7. Now last click on Start button
8. Wait until full process


Micromax Bolt A34 Format done with Volcano box Screenshot

Micromax Bolt A34 Format done with Volcano box Logs

  Detection initiated...  
  Vcc: null  
  Gnd: 7  
  Analyzing D+ and D-...  
  D+ = 4, D- = 3  
  Detection D+/D- with 0.94 seconds.  
  Continue to detect BOOT pin...  
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)  
  UsbVcc(VCC) = 1, BOOT(Pull Down) = 5  
  Setting...  
  Find USB device:SCI USB2Serial (COM177), (VID_1782&PID_4D00)  
  Pinouts setting complete!  
  Waiting for phone's response, press the Power on the phone    
  Internal version: SPRD3  
  Boot downloaded.  
  Start boot please wait a moment....  
  Spreadtrum Boot Block version 1.1  
  Boot downloaded.  
  Start analysis mobile data...  
 >>Set to Factory successfully.  

Sponsored Links

No comments:

Post a Comment

If any problem just write down your message on below comment box